flights, speed variators, electric motors

ť FLIGHTS

Material Fe 37 and similary

STANDARD LENGHT:
3 metres (ą 2%)

OUTSIDE DIAMETER:
is determined by taking the inside Ř plus twice the nominal material width and applying tolerances.

INSIDE DIAMETER:
is selected to be compatible with the sizes of tube on which the flight is to be installed.
Inside ř not less than one fifth of the outside Ř.

PITCH:
standard as out. Ř (less max. 2/3 out. Ř or plus max. 1,5 time out ř.

THICKNESS:
on ins. Ř double thickness than out. Ř

HAND FLIGHTS:
right and left to indicate on the order

Clockwise rotation:

flights clockwise rotation:

Right

Left

Flow

Attention: by overturning flight the sense of rotation doesn't change

TOLLERANCES

ř EXT. nominal

INSIDE ř

PITCH

OUTSIDE ř

fino a 150 mm.

150 - 250 mm.

250 - 500 mm.

-0 + 20/10

- 0 + 25/10

-0 + 32/10

ą 5 %

- 8/10 + 20/10

- 8/10 + 25/10

- 20/10 + 42/10

STANDARD PITCH:
conveyor flights are considered to be standard and are used for general conveying of most materials, pitch as out Ř

SHORT PITCH:
conveyor flights are frequently employed as feeders and are reccomended for inclined conveyors with an angle of more than 20° (pitches being less than 2/3 the out. Ř should be avoided; beyond out. Ř mm.300 superior reduction)

ONG PITCH:
conveyor flights provide a means for the agitation of liquids or the rapid conveying of very free flowing material (pitches being more than one and half times the outside Ř should be avoided).

RIBBON CONVEYOR:
flights are required for viscous, gummy or sticky materials which tend to adhere to flighting and pipe.

Influence of inclination over capacity

In order to calculate the PRODUCTION p/h we give approximate transport data which are not absolute, but only indicative, as a lot of factors will condition the final output: type, sizing and dampness of material, screw Ř, speed of rotation, inclination loading, etc.
Ex. Wheat: flight Ř 80 (pipe Ř 100) - speed R.P.M. 650/700: *

Inclination *	0°	15°	30°	45°	60°	90°
Production tons/hr.	10	9	7,5	6,5	6	3,5

INOX AISI 304 FLIGHTS- 3 mt. bars

CODE		EXT. DIAMETER mm.	PITCH mm.	PER SHAFT of mm.	THICKNESS EXT. BORDER mm.	Kg/mt.
Sx	Dx	EXT. DIAMETER mm.	PITCH mm.	PER SHAFT of mm.	THICKNESS EXT. BORDER mm.	Kg/mt.
0229	01	50	50	13.5	2.2	0.98
	0308	60	60	21.3	1.8	0.90
	0163	60	60	26.9	2.0	0.85
	076	65	65	30.3	2.0	0.85
0173	04	80	80	21.3	2.5	1.70
0285	05	80	80	26.9	2.4	1.58
06	031	80	80	33.7	2.7	1.40
061	0127	90	90	26.9	2.4	1.90
041	040	100	100	21.3	2.0	1.87
08	07	100	100	26.9	2.5	1.99
	085	100	70	33.7	2.5	2.50
037	035	100	100	33.7	2.5	2.00
	0251	110	110	42.4	2.5	1.95
	0283	120	80	33.7	2.0	3.13
0178		120	120	26.9	2.0	2.46
010	09	120	120	33.7	2.2	2.47
	011	130	130	33.7	2.4	2.63
090	082	130	130	42.4	2.2	2.51
0213	091	150	150	33.7	2.0	3.00
0123	012	150	100	48.3	2.4	3.93
014	013	150	150	48.3	2.4	2.94
0121	0120	150	150	60.3	2.5	2.76
028	015	160	160	48.3	2.4	3.01
	019	180	100	60.3	2.2	5.02
	0114	180	120	60.3	2.3	4.65
	0128	180	120	70.0	2.6	5.08
018	017	180	180	48.3	2.4	3.56
093	092	180	180	60.3	2.4	3.42
	0135	190	190	42.4	2.0	3.35
021	020	200	200	48.3	2.0	3.45
0214	0199	200	150	60.3	2.3	4.00
023	022	200	200	60.3	2.3	4.00
026	024	220	220	60.3	2.3	4.30
	095	230	230	48.3	2.0	4.50
0150	0208	230	230	60.3	2.0	4.23
026	025	250	250	60.3	2.0	4.35
049	048	250	250	70.0	2.0	4.34
0333	0332	250	200	76.1	2.0	5.34
	0327	300	250	76.1	2.0	5.34
0357	097	300	300	76.1	2.0	4.88
069	068	300	300	88.9	2.0	5.00
	0175	300	300	88.9	3.0	7.52
	038	350	300	88.9	3.0	10.56
	0273	350	350	88.9	3.0	9.00
079	0995	400	400	101.6	4-3.3	10/11
	0330	400	400	114.3	4-3.3	10.51

Continous iron flights - 3 mt. bars

CODE		EXT. DIAMETER mm.	PITCH mm.	PER SHAFT of mm.	THICKNESS EXT. BORDER mm.	Kg/mt.
Sx	Dx	EXT. DIAMETER mm.	PITCH mm.	PER SHAFT of mm.	THICKNESS EXT. BORDER mm.	Kg/mt.
474	809	50	47	13.5	1.7	0.70
2	1	50	50	13.5	1.7	0.70
188	187	60	60	21.3	1.7	0.90
9	8	70	70	17.2	1.5	1.10
11	10	80	80	17.2	1.7	1.30
13	12	80	80	21.3	1.7	1.30
15	14	80	80	26.9	1.7	1.15
631	17	85	85	21.3	1.8	1.55
20	19	90	90	26.9	1.7	1.40
22	21	100	100	21.3	1.6	1.55
24	23	100	100	26.9	1.7	1.60
27	26	100	100	33.7	1.8	1.50
31	30	120	120	26.9	1.6	1.90
37	36	120	120	33.7	1.8	1.90
39	38	130	130	26.9	1.6	2.00
41	40	130	130	33.7	1.7	2.00
43	42	130	130	42.4	1.7	1.90
47	46	135	135	26.9	1.5	2.00
50	49	135	135	33.7	1.7	2.10
52	51	135	135	42.4	1.7	1.90
54	53	140	140	33.7	1.6	2.10
56	55	140	140	42.4	1.8	2.15
	446	140	140	48.3	1.8	2.10
62	61	150	150	33.7	1.6	2.50
64	63	150	150	42.4	1.7	2.10
	65	150	100	48.3	1.7	3.45
67	66	150	150	48.3	1.8	2.30
1059	68	150	150	48.3	4.0	4.70
	1587	150	150	48.3	5.0	6.10
	481	150	150	60.3	2.0	2.20
150	454	150	150	60.3	4.5	4.90
73	72	160	160	42.4	1.6	2.40
75	74	160	160	48.3	1.6	2.30
561	560	160	160	48.3	4.0	5.30
465	280	170	170	48.3	1.7	2.50
1376	409	180	180	28.0	1.7	2.90
267	1214	180	180	33.7	1.8	2.80
77	76	180	180	42.4	1.6	2.60
	1362	180	180	42.4	4.0	6.30
79	78	180	140	48.3	1.5	3.00
81	80	180	180	48.3	1.7	2.60
524	82	180	180	48.3	3.4	5.40
84	83	180	180	60.3	1.7	2.60
632	85	180	180	60.3	4.3	6.20
	1588	180	180	60.3	6.0	8.60
	574	200	200	28.0	1.8	3.50
	674	200	200	28.0	3.0	5.80
91	90	200	200	48.3	1.8	3.20
92	532	200	200	48.3	3.5	6.20
	1610	200	200	48.3	5.3	10.10
95	94	200	200	60.3	2.0	3.40
1213	255	200	200	60.3	3.7	6.00
	1589	200	200	60.3	5.5	9.70
97	96	210	210	48.3	1.8	3.40
98	1538	210	160	60.3	1.8	4.10
	857	220	220	28.0	2.1	4.50
	858	220	220	28.0	2.8	6.40
103	102	220	220	48.3	1.8	3.50
105	104	220	200	60.3	1.9	3.60
107	106	230	230